Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
They are making a number of good points related to Tools You Need to Install a New Bathtub in general in the content on the next paragraphs.
Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily easily accessible, the project can relocate easily; if you have to open up a wall surface to eliminate the old tub and place the new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will require an assistant to vacate the old bathtub and embeded in the new one. Ensure you have actually qualified yourself for the work and also fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is better to think about employing one before you start. Possibilities are you may need an expert plumber to make tube links.
This post will aid you mount a new bathtub in your washroom if you have actually already purchased a brand-new tub and don't need to alter the plan of your previous water system pipes.
Your devices and material checklist must comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be rather problematic due to the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin making certain that the washers are in location between the tap and the sink. Protect the tap in place with the supplier provided backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical faucet adapters. The previous type needs to be attached to the faucet ends initially, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Using both wooden boards under its feet, put the tub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and check all joints and also new pipework for leakages and tighten them if essential. Load the bathtub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the tub must wait until the bathtub has been used at least when as this will resolve it right into its final setting.
Preparing for the Installment
To start with, the sustaining structure provided with the bath should be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to stop strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, causing issues with wetness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are sold in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to enable the movement experienced when the tub is in usage. The sealer can break rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily available on the market. It is a good idea to fit the tiles making use of waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our article on Installing A Bathtub. Thank you for finding the time to browse our article post. Do you know about somebody else who is in the market for the niche? Take a moment to promote it. Bless you for your time. Kindly visit our website back soon.
Source This Article Report this page